 | This article needs to beupdated. Please help update this article to reflect recent events or newly available information.(April 2014) |
| Eurotunnel Class 9 | |||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
 Locomotive 9834 in 2010 | |||||||||||||||||||||||||||||||
| |||||||||||||||||||||||||||||||
| |||||||||||||||||||||||||||||||
| |||||||||||||||||||||||||||||||
| |||||||||||||||||||||||||||||||
TheEurotunnel Class 9 orClass 9000 are six-axle high-powerBo′Bo′Bo′ single-ended electric locomotives built by theEuroshuttle Locomotive Consortium (ESCL) ofBrush Traction andABB. The class was designed for and is used exclusively to haul theLeShuttle road vehicle services through theChannel Tunnel.
Tendering for the locomotive procurement began in 1989. The specification included; a top speed of 160 km/h (100 mph); a terminal-to-terminal travel time of 33 minutes pulling a 2,100-tonne (2,067-long-ton; 2,315-short-ton) train; an axle load limit of 22.5 tonnes (22.1 long tons; 24.8 short tons); anoperating temperature range between −10 °C (14 °F) and 45 °C (113 °F);[6] aloading gauge within the UIC 505-1 standard; a minimum curve radius of 100 m (5 chains);[7] be able to start a shuttle train on a 1 in 160 (0.625%)gradient with one locomotive bogie inoperative (at 0.13 m/s2 (0.43 ft/s2)), and a single locomotive should be able to start the train on the same gradient if the other locomotive failed.[6][7] The operating concession agreement betweenthe tunnel operator and the British and French governments required that there be a locomotive on either end of the train, allowing the reversing or splitting of the train in an emergency.[6]
The design specifications implied a minimum power of 5.6 MW (7,500 hp), and also meant that a four-axle design would not be guaranteed to be able to supply sufficient tractive effort. ESCL proposed a six-axle Bo′Bo′Bo′ locomotive derived from thenarrow-gaugeEF class locomotives supplied byBrush Traction to theNew Zealand Railways Corporation and won the contract with an initial order of 40 in July 1989.[6][1][8]
The main traction electrical system consists of:[note 1] two pantographs (duplicated for redundancy) collecting a 25 kV AC supply which feeds the main transformer, with separate output windingsrectified to a DC link (one per bogie) using four quadrant converters. The direct current drives a three-phase inverter, which powers two asynchronous three-phase induction motors.[4][9] There are two additional output windings on the transformer for the locomotive's auxiliaries and to supply power to the train vehicles.[4]
The bogies were a fabricated steel design, with coil spring primary suspension. The traction motors and gearboxes (one per axle) were mounted to the bogie frame and connected to the wheels by a flexibly coupledquill drive. Traction links were connected to the bogie frame at a height of 200 mm (7.87 in) above rail. The locomotive superstructure is supported on coil springs on a central swing bolster, and the centre bogie allows 200 mm (7.87 in) of lateral movement to negotiate small-radius curves.[1] Yaw dampers are also fitted.[1]
The locomotive superstructure is a stressed-skin monocoque design.[1] Both the bogies and superstructures were fabricated by Qualter, Hall and Company ofBarnsley.[10]
The driver's cab and exterior design of the locomotives was undertaken by DCA Design.[11] Side windows in the locomotive cab are omitted to prevent 'segment flicker' caused by fast running in the tunnel, a potential distraction and cause of operator drowsiness.[12] The operator's cabin is air conditioned and pressurised for comfort.[6] The locomotive uses in-cabTVM 430 signalling.[13] The driving cab also incorporates train manager's facilities, including safety systems such as CCTV, alarms and communication links. There is a second driving position for shunting at the rear of the locomotive.[6][note 2]
The initial order for 40 units was reduced to 38,[1] numbered 9001 to 9038.[13] The first locomotive was completed in 1992, and two units (9003 and 9004) were tested at theVelim test track in the Czech Republic.[13] Locomotive 9004 started its required 50,000-kilometre endurance test at Velim on 17 August 1993 and finished it on 23 September 1993.[14]
The locomotives are maintained at the Eurotunnel depot located just besideEurotunnel Calais Terminal atCoquelles near Calais, France.[13][note 3]
The formal opening took place on 6 May 1994 withQueen Elizabeth II andFrançois Mitterrand travelling on a shuttle through the tunnel.[13]
The1996 Channel Tunnel fire damaged locomotive 9030 beyond repair. It was scrapped in 1997 at the Coquelles depot.
In 1997, Eurotunnel ordered five more locomotives and in 1998 the order was increased to a total of 14. This second batch of locomotives also had small improvements compared to the originals, includingIGBT-based traction inverters instead ofGTO-based and one inverter per motor instead of one per bogie.[2]
This second batch of locomotives is numbered in the 9100 series (9101 to 9113) except for one locomotive, 9040 which was purchased as a replacement for 9030, the locomotive destroyed in the 1996 fire.[13]
In 1999, Eurotunnel ordered seven locomotives with an increased power of 7 MW (9,387 hp). This third batch of locomotives was delivered between 2001 and 2003, and is numbered in the 9700 series (9701 to 9707).[15][13] The higher power output allowed an increase in the length and weight of cargo shuttle trains.[13]
.jpg)
Since 2000, Eurotunnel has been slowly rebuilding the older 9000 and 9100 series locomotives from 5.6 to 7 MW (7,500 to 9,400 hp), replacing the main transformer, traction converters and motors.[5] These rebuilt locomotives are numbered in the 9800 series.
By late 2017 of the 57 locomotives, 45 of them had been upgraded to the 7 MW (9,400 hp) standard, while the remaining 12 had the original 5.6 MW (7,500 hp) power.[16]
| Number range | Built | Power | Notes |
|---|---|---|---|
| 9001–9038 | 1992–1994 | 5.6 MW (7,500 hp) | 9030 withdrawn due to fire damage |
| 9040 | 1998 | Built to replace fire-damaged locomotive 9030 | |
| 9101–9113 | 1998–2001 | Dedicated to freight shuttles | |
| 9701–9707 | 2001–2002 | 7 MW (9,400 hp) | |
| 9801– | Rebuilt 2004–2012 | Rebuilt from 5.6 MW (7,500 hp) machines |
After introduction the locomotives were named after opera singers. In 1997 four units were namedJungfraujoch,Lötschberg,Gotthard andFurkatunnel, after Swiss rail tunnels.[17]
| Number | Name |
|---|---|
| 9005 | Jessye Norman |
| 9007 | Dame Joan Sutherland |
| 9011 | José van Dam |
| 9013 | Maria Callas |
| 9015 | Lötschberg 1913 |
| 9018 | Wilhelmenia Fernandez |
| 9022 | Dame Janet Baker |
| 9024 | Gotthard 1882 |
| 9026 | Furkatunnel 1982 |
| 9029 | Thomas Allen |
| 9033 | Montserrat Caballé |
| 9036 | Alain Fondary |
| 9037 | Gabriel Bacquier |
| 9801 | Lesley Garrett |
| 9802 | Stuart Burrows |
| 9803 | Benjamin Luxon |
| 9804 | Victoria de los Ángeles |
| 9806 | Régine Crespin |
| 9808 | Elisabeth Söderström |
| 9809 | Françoise Pollet |
| 9810 | Jean-Philippe Courtis |
| 9812 | Luciano Pavarotti |
| 9814 | Lucia Popp |
| 9816 | Willard White |
| 9819 | Maria Ewing |
| 9820 | Nicolai Ghiaurov |
| 9821 | Teresa Berganza |
| 9823 | Dame Elisabeth Schwarzkopf |
| 9825 | Jungfraujoch 1912 |
| 9827 | Barbara Hendricks |
| 9828 | Kiri Te Kanawa |
| 9831 | Plácido Domingo |
| 9832 | Renata Tebaldi |
| 9834 | Mirella Freni |
| 9835 | Nicolai Gedda |
| 9838 | Hildegard Behrens |
