DIN 7876 is a Germanstandard specifying howswimming fins should be dimensioned, tested and marked for conformity. In 1980, theDeutsches Institut für Normung (DIN) published consecutively numbered German standards DIN 7876,DIN 7877 andDIN 7878 dedicated respectively to theswimming fin, thediving mask and thebreathing tube, which constitute basic underwaterdiving equipment. DIN 7876 of October 1980 is entitledTauch-Zubehör – Schwimmflossen – Maße, Anforderungen und Prüfung in German and subtitled “Diving accessories for skin divers; Flippers, dimensions, requirements and testing” in English.[1] This standard establishes certain quantitative and qualitative specifications for swimming fins, with particular reference to foot pockets and heel straps. Swimming fin manufacturers fulfilling such requirements may mark their products as compliant with this standard. The status of DIN 7876 is currentlyzurückgezogen, meaning: “withdrawn”.
DIN 7876 is the third of the seven known military, national and international standards on swimming fins listed below in order of publication:
DIN 7876 may be applied to allfull-foot and open-heel fin models made from either rubber or plastic, but the standard excludes long-bladed fins for competitive use. In the interests of health and safety, this standard stipulates that no protruding edges should be in evidence at any point of contact between the fins and the feet. If heel straps are present, they should be adjustable and retain their settings when wet. A 10-minute pull test is prescribed to confirm this requirement.
The bulk of DIN 7876 is devoted to the dimensions of the footspaces offull-foot and open-heel fins. A full-foot fin is designated as a "Form A" fin, while an open-heel fin is designated as a "Form B" fin, which coincides with fin nomenclature in the earlier 1977USSR andCIS StandardGOST 22469—77 entitledЛасты резиновые для плавания. Общие технические условия in Russian and subtitled "Swimming rubber flippers. General specifications" in English.
The key footspace measurements required by DIN 7876 are the inner length "FL" (Fußlänge or Foot Length) at the longest dimension and the inner width "FB" (Fußbreite or Foot Width) at the widest point. The standard provides a table, based on theMondopoint shoe-sizing system, with a range of recommended foot widths for each foot length in millimetres.
DIN 7876 requires any fins complying with its specifications to be marked with their footspace length (FL) and width (FB) in millimetres as well as the name or symbol of their manufacturer, distributor or importer. This practice is illustrated here in the image of the sole of a European size 46-48 full-foot fin made in Italy during the 1980s. "DIN 7876-A" identifies this product as a German Standard DIN 7876 compliant full-foot fin (aka Form A), whose footspace measures 275 mm in length (FL) at the longest dimension and 105 mm in width (FB) at the widest point with a tolerance of ±2 mm.
For reasons of economy, swimming fins are traditionally sized to accommodate a range of severalshoe sizes. The upshot is that a model labelled with a 46-48 size range risks being a loose fit on a size 46 foot and a tight fit on a size 48 foot. A loose-fitting fin is liable to slip off in heavy surf, while a tight-fitting fin is likely to cause foot cramping, both potentially disastrous consequences if the user is far from the shore. A DIN 7876 compliant fin comes embossed with the length and width of its footspace in millimetres, enabling the purchaser to make a more precise match between the fin and the foot.
References to DIN 7876 can be found in the literature of underwater diving and in the publications of theGerman Life Saving Association and theGerman Red Cross.[9][10][11] In a 1994 circular, theFrench Ministry of Education cited the standard when setting selection criteria for water sports equipment to be used by children between the ages of 4 and 12.[12]
Although DIN 7876 is now officially in abeyance, its legacy survives within the normative documentation of other standardisation bodies.Austrian standard ÖNORM S 4224 of 1988 entitled "Tauch-Zubehör; Schwimmflossen; Abmessungen, sicherheitstechnische Anforderungen, Prüfung, Normkennzeichnung" in German and subtitled "Diving accessories; fins; dimensions, safety requirements, testing, marking of conformity" in English, closely resembles DIN 7876 in content. DIN 7876 foot-pocket and heel-strap dimensioning provisions remain in force within Malaysian standard MS 974 entitled "Specification for rubber swimming fins", published in 1985 and revised in 2002. European standard EN 16804 entitled "Diving equipment — Diving open-heel fins — Requirements and test methods" and published in 2015 emulates DIN 7876 in requiring the heel strap to be pull-tested for slippage and the footspace to be free of sharp edges that may cause injury.
{{cite journal}}:Cite journal requires|journal= (help)
