| RB Conestoga | |
|---|---|
.jpg) | |
| General information | |
| Type | Military transport aircraft |
| National origin | United States |
| Manufacturer | Budd Company |
| Status | Retired |
| Primary users | United States Navy |
| Number built | 20 |
| History | |
| Introduction date | 1944 |
| First flight | 31 October 1943 |
TheBudd RB-1 Conestoga was a twin-engine,stainless steelcargo aircraft designed for theUnited States Navy duringWorld War II by theBudd Company ofPhiladelphia, Pennsylvania. Although it did not see service in a combat theater, it pioneered design innovations in American cargo aircraft, later incorporated in modern military cargo airlifters.
World War II created a great demand for military transport aircraft in the United States. Because of initial fears of a shortage ofaluminum, theWar Department explored the use of other materials for aircraft construction. Budd, the developer of theshotweld technique for welding stainless steel and a manufacturer of stainless steel railroad cars, automobile, bus, and truck bodies, hired an aeronautical engineering staff and worked with theU.S. Navy to develop a new twin-engine transport aircraft constructed primarily of stainless steel. The U.S. Navy accepted the proposal for the new aircraft, and placed an order for 200, to be designatedRB-1. TheU.S. Army Air Forces (USAAF) followed with an order for 600, designatedC-93.
The Conestoga was a twin-engine high-wingmonoplane withtricycle landing gear. The elevated flight deck was contained in a distinctive, almost hemispherical nose section. Its two 1,200 hp (890 kW)Pratt & WhitneyR-1830-92 air cooled 14-cylinder, twin-row,radial engines, the same engines fitted to theC-47, drove three-bladedHamilton Standard Hydromatic constant-speed, full-featheringpropellers and powered a 24-volt electrical system. While the fuselage was thin-gauge stainless steel, only a portion of the wing was made of the metal; the trailing section of the wing and all control surfaces were fabric-covered.
The RB-1/C-93 was radical for its day, introducing many of the features now standard in military transports. The flight deck could accommodate three crew members, pilot and copilot side-by-side, the navigator behind them. Stairs connected the flight deck to the cargo area, which was 25 feet (7.6 m) long with an unobstructed cross-section of 8 × 8 feet (2.4m) throughout its length. Cargo loading and unloading could be accomplished in two ways: through 40 × 60 inch (102 × 152 cm) doors on both sides of thefuselage or by an electrically operated 10 × 8 foot (3.0 × 2.4 m) ramp at the aft end of the cargo area under the upswepttail, a similar development to what had been initially fitted to the Germans' ownJu 290 four-engined transport aircraft as theirTrapoklappe ramp in 1939. The RB-1's loading ramp, accessed by manually operated clamshell doors, along with the tricycle landing gear, meant cargo could be loaded/unloaded at truck-bed height. A manually operated two-ton (1814 kg) hoist for unloading trucks and a one-ton winch for pulling cargo up the ramp were also provided in the cargo area. The aircraft could accommodate:
The prototype first flew from the Budd Red Lion Factory Airfield in Philadelphia, Pennsylvania on 31 October 1943, piloted by Guy Miller.[1] The prototype had a takeoff run when empty of just 650 feet (200 m), and could carry a maximum payload of 10,400 pounds (4,700 kg) with a takeoff run of 920 feet (280 m).[2] However, the aircraft demonstrated greater than expected fuel consumption; the range with a standard payload was only 700 miles (1,100 km), 650 miles (1,050 km) with a maximum payload.[2] Three prototype aircraft:NX37097,NX41810, andNC45354 were built; one was used for testing radio equipment, while the other two were used for flight test evaluations.[1][3] During testing, a few aircraft had difficulty with the simultaneous deployment of the right and left landing gear. With the same engines as the C-47, but 3,000 pounds (1,400 kg) heavier (empty), the aircraft was relatively underpowered; it was reportedly said[by whom?] that, for an aircraft built by a railroad car company, it indeed handled like one.[citation needed]
At the Budd factory and airfield in Philadelphia, Pennsylvania, there were construction delays due to cost overruns and problems with stainless steel fabrication. By late 1943, aluminum production had been increased with the construction of new processing facilities, and other more conventional cargo aircraft (such as theCurtiss C-46 Commando and theDouglas C-47 Skytrain) were being produced in large numbers. This caused the Army to cancel its order for the C-93 and the Navy to reduce its RB-1 order from 200 to 25, of which 17 were delivered in March 1944.
On 13 April 1944, during aNaval Air Training Command (NATC) evaluation flight of RB-1 prototype U.S. NavyNX37097 atPatuxent River NAS, Maryland, the aircraft crashed, killing one of the crew.[4] The aircraft was damaged beyond repair and written off, but the pilot reported that the stainless steel construction of the aircraft contributed to saving his life.
Production RB-1 aircraft never entered squadron service with the Navy, but a few were briefly used byNaval Air Stations as utility aircraft. With only 17 aircraft in inventory, the RB-1 was not feasible to maintain on the active list, and it was retired from U.S. Navy service in early 1945. The extant RB-1s were then transferred to theWar Assets Administration (WAA) to be sold as war surplus. In 1945, the WAA sold 12 Conestogas to theNational Skyway Freight Corp[5] for $28,642 each (equivalent to $394,500 in 2024 dollars) at a time when new C-47s were selling for approximately $100,000 each (equivalent to $1.4 million in 2024 dollars). The new company, founded by members of theAVGFlying Tigers immediately sold four RB-1 aircraft to other buyers, which paid for the entire WAA contract.[5]
The seven remaining National Skyways aircraft were used to transport a variety of cargo, shipping fruit and furniture from its base inLong Beach, California.[N 1] Pilots reported that the Budd transports were temperamental; in particular, exhaust stacks kept falling off and causing engine fires.[5]There were three more crashes of Conestogas while in service with National Skyway Freight, one each inVirginia,New Mexico, andMichigan.[5][N 2] The crash in Virginia was a belly landing at a country club brought on by fuel exhaustion following weather-related problems. The Albuquerque, New Mexico crash was due to a downdraft during a snow storm, 80 miles (130 km) from Albuquerque.<Widow of Lawrence Molloy Feemster, Ruth Mae (Feemster) Hill & preserved newspaper clippings>[better source needed] Pilot and copilot were killed when they were thrown through the windshield and the aircraft skidded over them; the flight engineer survived.[5]
In 1947, the U.S. Army (and later the U.S. Air Force) gave National Skyway Freight a large contract for trans-Pacific freight, for which it leased military aircraft. The company changed its name toFlying Tiger and replaced the RB-1s with C-47s for its U.S. freight routes; the RB-1s were sold off to other buyers. One of these aircraft, a prototype RB-1, "NC45354" was sold to theTucker Motor Company to transport its demonstration1948 Tucker Sedan to auto shows around the U.S.; it was reportedly later abandoned at an airfield in Oakland, California after repeated mechanical troubles.[5]
The V.A.S.D. (Viação Aérea Santos Dumont) was born on January 18, 1944. He started with the purchase of two Catalinas and a Budd Conestoga, both former Rubber development Corporation. Budd RB.1 Conestoga had the PP-SDC "Tio Sam" enrollment. It was damaged in an emergency landing atCampo dos Afonsos on 04.01.1947, landing with one train collected, declared unrecoverable and there scrapped.[citation needed]
A single unrestored Budd RB-1, BuNo 39307, is on display at thePima Air & Space Museum inTucson,Arizona.[6]
Data from Jane's fighting aircraft of World War II[7]
General characteristics
Performance
