| A-213 Totem | |
|---|---|
 | |
| General information | |
| Type | Utility and fisheries seaplane |
| National origin | Canada |
| Manufacturer | Boeing Aircraft of Canada |
| Designer | CaptainEdward Fothergill Elderton |
| Status | Scrapped in 1942 |
| Primary users | Canadian Airways |
| Number built | 1 |
| History | |
| Introduction date | 1932 |
| First flight | June 1932[1] |
TheBoeing-Canada A-213 Totem was a Canadian single-enginepushermonoplaneflying boat intended for forestry and fisheries patrols as well as a light utility transport for theBritish Columbia coastline, where there are few flat places for runways, and waterways are plentiful. The sole example,CF-ARF, CB10[2] was designed and built byBoeing Aircraft of Canada. The name refers to theTotem poles used by theFirst Nations inBritish Columbia.[3]
The Chief Engineer,Edward Fothergill Elderton was British, and had previously worked atShort Brothers[4] andSaunders-Roe before coming to Canada to work forCanadian Vickers and Boeing of Canada.[3]
Despite being developed while theBoeing 40H-4 andC-204 were under construction, the Totem's design owed little to Boeing aside from the Boeing 103airfoil section and the rudder shape.[3] Indeed, previous Boeing flying boats used wood extensively in the hull, and the 40H-4 used welded steel tubes for its fuselage structure. Instead, itstumblehome and heavy external ribs on the hull showed a strong Saunders-Roe influence, which is unsurprising given the Chief Engineer's background.[3] The model number A-213 fits numerically in the Boeing sequence but the significance of the 'A' prefix remains unexplained.[3] It may be a coincidence that Saunders-Roe was using an A as a prefix for all their aircraft at that time.
The bottom of the hull was built up as a three-plyAlclad sandwich, riveted to frames with external longitudinal stringers. The sides and top of the hull used sheet metal with widely spaced corrugations or ribs.[4] There were five bulkheads separating six watertight compartments, and it made extensive use of stainless steel components to limit corrosion.[4] The roomy 4 seat cabin was positioned ahead of the front wing spar and was accessed through a folding roof hatch.[4][3] Dual controls were offered, while the stick could be removed on the passenger side.[4]The main fuel tank was behind the cabin and between the wing spars, with a smaller fuel tank in the engine nacelle that was fed by a fuel pump.[4] TheWasp Jr.radial engine was mounted as a pusher, which made passenger egress safer, and reduced cabin noise.[4] Starting was accomplished with an inertial hand starter.[4]
The wings were built around twospruce spars, with ribs and leading and trailing edges in spotweldedchromium-molybdenum alloy (chrome-moly) steel, all covered in fabric sealed and tightened withaircraft dope.[4] The wings were braced with parallel steel struts to the hull chines, and fitted with metal tip floats.The high mounted elevators, fin and rudder were like the ribs, made up from spot welded chrome-moly steel, covered in fabric.[4]All controls were actuated via push-pull rods, with no cables or pulleys to jam.[4]Unusually for the time, a retractable water rudder was fitted that would pivot back and up if it struck an obstacle.[4]
The sole Totem built, serial number CB10 was registered as CF-ARF.[2] The first known flight is believed to have been on 16 June 1932, byWilliam J. Holland.[3] Test flights were being made in July by company pilots, and on September 25, an official test flight was made, with government observers.[3] One of the test flights was toGaribaldi Lake, the first visit by an airplane to that lake, at an altitude of 4,869 ft (1,484 m) where it experienced no difficulties.
Boeing of Canada had been having difficulty selling its flying boats, and the Totem was no exception, with it remaining in Boeing's hands for almost a year before being sold to a private operator.[5]
In May 1933, the Victoria Daily Times reported that Holland was taking the president ofUnited Aircraft and Transport Corporation, (part owner of both Boeing and Boeing of Canada) for a "leisurely" flight up the British Columbia coastline toJuneau, Alaska.[6]In July 1933, Holland took the Totem toAmethyst Lake inJasper National Park, toLake Louise inBanff National Park and toLake Minnewanka.[5] He gave joyrides to the locals for $5 a flight, while also occasionally doing local charters, including taking the manager of theBanff Springs Hotel to theColumbia Icefield and another longer one for a group of fishermen toMarvel Lake (north of Marvel Peak).[5] The Totem was not the first aircraft to visit Banff though, as they were preceded by aNorman Thompson N.T.2B flying boat operated by theRocky Mountain Aviation Transport Company between 1921 and 1924.[5] Holland was notified in August that the Totem had been sold and to make haste back to Vancouver to transfer the airplane to the new owner.[5]
The new owner only kept it for a couple of years before selling it toCanadian Airways in May 1935.[7] This was despite demonstrating excellent water and flight handling characteristics during official tests and in operational service.[3] It would remain in service until January 1938, mainly carrying out fisheries patrols,[3] until they sold it to another private operator in 1938.[7] Its registration was cancelled in February 1942, and presumably scrapped.[7][3]
The Totem served most of its career in British Columbia, however it would remain a one-off as pure-flying boats were by then being supplanted by floatplanes.[3]
Data from Flight, 1932, p.890-892
General characteristics
Performance
.svg)