Anautomobile auxiliary power outlet (also known ascar cigarette lighter,vehicle cigarette lighter orauxiliary power outlet[1]) in anautomobile was initially designed to power an electrically heatedcigarette lighter,[1] but became ade facto standardDC connector to supply electrical power for portable accessories used in or near an automobile directly from the vehicle's electrical system. Such items includemobile phone chargers,cooling fans, portablefridges, electricair pumps, andpower inverters.[1]
In most vehicles, at least one car outlet is present. Some vehicles may have more power outlets: usually one for the front passengers, one for the rear passengers and one for the luggage trunk.
Thevoltage of the power outlet is usually near 12 VDC, and may be elevated between 13.5 V to 15 V while the engine is running. Ontrucks, the voltage of the power outlet may be near 24 V DC.
The 12 V power circuit is protected by acar fuse, often rated at 10 to 20 amperes, which provides 120 to 240 watts of power. Large appliances such as hair dryers or toasters draw too much power to be fed from an auxiliary power socket. If wired directly rather than through the ignition, an empty car battery can be charged through the outlet from an external power source, which is more convenient albeit slower than currents supported through electrical clamps on the car battery.[2]
Many modern vehicles no longer have the auxiliary power outlet, with it being replaced byUSB 2.0 orUSB-C ports.[3]
The electrical cigar-lighter was invented and patented in the early 1880s by the Swiss-Austrian inventorFriedrich Wilhelm Schindler.[4] In the 1890s, these tools were sold as electrical cigar lighters (Cigarrenanzünder, laterZigarrenanzünder) in the major German warehouse catalogues.[citation needed] Before theGreat Depression, cigarettes overtook cigars in sales, and they became more popularly known as "cigarette lighters", though they have remained the diameter of a standard cigar of 21 millimetres (0.83 in), or a 52ring gauge.
In 1921, the MorrisU.S. patent 1,376,154 was issued for a so-called "wireless" or "cordless" lighter with a removable element. The igniter was heated in the socket and then manually removed for use after an appropriate time interval.[5]
In the United States, cigarette lighters started appearing in 1925-1926 in some models. They were a standard feature by the 1950s.[6]
In 1928, the Connecticut Automotive Specialty Company (Casco) inBridgeportpatented its version of an automotive cigarette lighter, which used a cord and reel.[7] In the reel-type lighters, the igniter unit was connected with a source of current by a cable that was wound on a spring drum so that the igniter unit and cable could be withdrawn from the socket and be used for lighting a cigar or cigarette. As the removable plug was returned to the socket, the wires were reeled back into it. The circuit was closed either by pressing a button or removing the igniter from its socket.[5]
The modern "automatic" removable automotive V-Coil lighter was developed by Casco in 1956,[7] for which it receivedU.S. patent 2,959,664, issued in 1960.
The sockets and mating plugs are defined in the ANSI/SAE J563[8] specification. For the 12-volt systems, the center contact is the positive terminal and the shell is the negative terminal. Most automobiles connect the negative terminal to the frame of the vehicle (negative ground).
12-volt auto connectors are made to comply with a standard byUnderwriters Laboratories for safety. UL2089 was developed to cover the requirements for portable adapters rated 24 V DC or less that are intended to be supplied from the battery-powered electrical system of a vehicle. Products covered by the standard include cord assemblies of a plug that mates with the standard cigarette receptacle found in automobiles.
Plugs often include apilot lightLED indicator to indicate that electrical power is connected. Optionally, the plug may be equipped with an internalfuse for electrical safety, usually rated at 10 amps or less.[citation needed] In some designs, the tip of the plug may be unscrewed to reveal a cylindrical glass fuse; other variants may use a blade-type fuse inserted into the side or back of the plug.
The lighter is a metal or plastic cylinder containing a thin flat coil ofnichrome metal strip, through which high current (≈10amperes) passes when the device is activated, usually by pushing it into the socket as though it were apush-button. When pushed in, the lighter is held against the force of a spring by a clip attached to abimetallic strip.[9] Theheating element glows orange hot in seconds, causing the bimetallic strip to bend and release the mechanism. The handle pops out, eliminating the need for the user to time the heating operation. If the lighter is then promptly removed from its socket, it can light a cigarette, cigar, ortinder.
A common feature of Italian cars in the 1960s to the 1970s, such as Alfa Romeos and Ferraris, is the Brico Pram cigarette lighter, which differs from conventional designs in that the lighter does not pop out for removal to light a cigarette, even though it visually resembles the traditional design. Instead, the center of the lighter features a tapered opening for the user to insert a cigarette until it touches the heating element, the rim of the handle is then pressed down to activate the lighter, the heating element then lights the cigarette and disengages the circuit with an audible ping once the desired temperature is reached as per a conventional lighter. The advantage of such a design is in safety as the red-hot heating element cannot be accidentally dropped onto an occupant's lap. Still, it takes away the ability for the lighter to be removed for the receptacle to be used as a power outlet, and it also does not allow cigars to be lit as the opening is not large enough.
In newer cars, the socket is equipped with a plastic cover without the lighter heating element.[10] However, the socket has been repurposed and continues to be used to powerconsumer electronics in vehicles.[11] Often, a vehicle may come with several outlets for convenience, some in the rear passenger area of the vehicle or the cargo area, for powering portable devices. These outlets usually have a plastic cap tethered to them, and are usually labeled as being only for DC power, because they are not intended to withstand the heat produced by an electrical cigarette lighter.
The use of cigarette lighter receptacles to supply 12 volt DC power is an example ofbackward compatibility to ade facto standard. As a power connector, the lighter receptacle is larger, harder to use and less reliable than other DC connectors[citation needed]. There are two prong threaded plugs to stop the plug from falling out due to vibrations.[12]
Cigarette lighter receptacles are in widespread use in many highway vehicles and some boats. Portable cigarette lighter receptacles attached to cables andalligator clips for connection directly tocar batteries are available for temporary use. In newer vehicles, one or moreUSB connectors may also be provided. Plus in newer cars, the power output from the lighter plug is so reliable that it can charge laptops, without any voltage problems.[dubious –discuss]
Standardized 12 volt DC automobile plugs are defined in the United States byUL Standard 2089 regarding vehicle battery adapters. This standard covers plugs and cord sets that insert into cigarette lighter receptacles. In Europe, 12 volt plugs and sockets are not specially regulated and do not require approvals for theCE mark.[citation needed]
The male plug is sometimes used to feed powerinto a vehicle to recharge its battery because it usually has no regulatory circuitry between the outlet and the car battery. For instance, portable solar battery maintainers generally connect to a vehicle's battery in this manner.Trickle chargers also sometimes connect in this way, eliminating the need to leave a vehicle's hood open, as well as eliminating the possibility of reversed polarity. Most cars nowadays are designed with a battery-negative earthing system and therefore have a +12V positive power distribution. In such a case, the centre pin of a plug/socket will be +12V DC and the outer casing 0V. While polarity is not an issue for a cigarette lighter, it is prudent to verify the correct matching of polarities when connecting other kinds of accessories.
In some models, the cigarette lighter outlet is not powered when the ignition key is removed and charging is not possible, though modification of the fuse box may allow unlocking continuous power output, by establishing aparallel circuit from a continuously powered fuse slot through a "piggyback" connector.[13]
Since the cigarette lighter socket was originally designed only to heat a cigarette lighter, repurposing these sockets as generic power connectors can lead to many problems. In addition to the issues with partially-compatible physical dimensions, the plugs can vibrate out of the socket under normal driving conditions, owing to poor retention. Also, there have been reports of melted plug tips due to poor contact and heat generation fromohmic resistance.
A second problem is that nominally "twelve-volt" power in cars fluctuates widely. The outlet is connected directly to the electrical system of the car. The actual voltage, matching the car battery's voltage, will be approximately 12.5 volts when dormant (less in cold conditions), approximately 14.5 volts when the engine and the alternator/generator are operating (more when cold), and may briefly drop as low as 5–6 volts during engine start due to the high temporary battery current usage.[14] When used,DC to DC converters will usually compensate for small fluctuations, but reliable power may not be available without an independent battery-powereduninterruptible power supply.
Rarely, more extreme cases of voltage fluctuation can occur when the car battery is disconnected while the engine is running, or when the car receives ajump start. When the battery is disconnected while the engine is running, its voltage smoothing effect (similar tocapacitors) is unavailable and aload dump transient can produce very high voltages as the built-involtage regulator has been controlling the alternatorfield current to charge the vehicle battery and although it will attempt to reduce the field current to keep the output voltage constant, the field winding is highly inductive and setting the current to its new value takes several hundred milliseconds, during which the alternator output voltage will exceed its intended value. The load dump transient may also ruin thediodes in thealternator by exceeding their breakdown voltage. A car receiving a jump start from a truck may be subject to a 24 V electrical system used in some vehicles.[15] Also, a "double battery jump-start" is performed by some tow truck drivers in cold climates.[16]
Equipment intended to be powered by the receptacle needs to account for intermittent contact, and voltages outside the nominal12 V DC, such as maximum voltage9–16 V continuously, or maximum voltage of20 V lasting1 hour,24 V lasting1 minute, and40 V lasting400 ms.[17] An example of protection component ratings tolerance is+50 to−60 V DC.[18] Robust equipment must tolerate temperatures varying between −40 and +85 °C (−40 and 185 °F), plus possible high humidity and condensation of water.[17]
The maximum operating voltage for 14 V systems is specified at 24 V, representing a double battery jump-start condition.
Another steady-stateOV condition is the double-battery jump start, which occurs when atow truck or other service personnel use 24 V to jump-start a disabled vehicle or otherwise charge a dead battery. The typicalOEM test requirement for this condition is about 24 V for two minutes. Some systems related to safety and engine management are required to operate under these conditions.
Car interior | |
|---|---|
Part of a series of articles oncars | |
| Instruments | |
| Controls | |
| Anti-theft | |
| Other elements | |
| Convenience | |
