Ananvil is ametalworkingtool consisting of a large block of metal (usuallyforged orcast steel), with a flattened top surface, upon which another object is struck (or "worked").
Anvils are massive because the higher theirinertia, the more efficiently they cause theenergy of striking tools to be transferred to the work piece. In most cases the anvil is used as aforging tool. Before the advent of modernwelding technology, it was the primary tool of metal workers.[1]
The great majority of modern anvils are made of caststeel that has been heat-treated by eitherflame orelectric induction. Inexpensive anvils have been made ofcast iron and low-quality steel, but are considered unsuitable for serious use, as they deform and lack rebound when struck.
The largest single piece tool steel anvil that is heat-treated is 1600 pounds (726 kg). This anvil was made in 2023 by Oak Lawn Blacksmith. There are larger anvils that are made out of multiple pieces such as “The mile long anvil” made by Napier which weighs 6500 pounds (2948 kg). This anvil is not heat-treated or made from tool steel.
The primary work surface of the anvil is known as the face. It is generally made of hardened steel and should be flat and smooth with rounded edges for most work. Any marks on the face will be transferred to the work. Also, sharp edges tend to cut into the metal being worked and may cause cracks to form in the workpiece. The face is hardened and tempered to resist the blows of the smith's hammer, so the anvil face does not deform under repeated use. A hard anvil face also reduces the amount of force lost in each hammer blow. Hammers, tools, and work pieces of hardened steel should never directly strike the anvil face with full force, as they may damage it; this can result in chipping or deforming of the anvil face.
The horn of the anvil is a conical projection used to form various round shapes and is generally unhardened steel or iron. The horn is used mostly in bending operations. It also is used by some smiths as an aid in "drawing down" stock (making it longer and thinner). Some anvils, mainly European, are made with two horns, one square and one round. Also, some anvils are made with side horns or clips for specialized work.
Thestep is the area of the anvil between the "horn" and the "face". It is soft and is used for cutting; its purpose is to prevent damaging the steel face of the anvil by conducting such operations there and so as not to damage the cutting edge of the chisel, though many smiths shun this practice as it will damage the anvil over time.
Anvil with upsetting block
There have also been other additions to the anvil such as an upsetting block; this is used to upset steel, generally in long strips/bars as it is placed between the feet of the anvil. Upsetting is a technique often used by blacksmiths for making the steel workpiece short and thick, having probably been originally long and thin.
Thehardy hole is a square hole into which specialized forming and cutting tools, calledhardy tools, are placed. It is also used in punching and bending operations. These are not to be confused withswage blocks, although their purpose is similar.
Thepritchel hole is a small round hole that is present on most modern anvils. Some anvils have more than one. It is used mostly for punching. At times, smiths will fit a second tool to this hole to allow the smith more flexibility when using more than one anvil tool.
The anvil is placed as near to the forge as is convenient, generally no more than one step from the forge to prevent heat loss in the work piece. An anvil needs to be placed upon a sturdy base made from an impact and fire resistant material. Common methods of attaching an anvil are spikes, chains, steel or iron straps, clips, bolts where there are holes provided, and cables.
The most common base traditionally was a hard wood log or large timber buried several feet into the floor of the forge shop. In the industrial era, cast-iron bases became available. They had the advantage of adding additional weight to the anvil, making it more stable. These bases are highly sought after by collectors today. When concrete became widely available, there was a trend to make steel-reinforced anvil bases by some smiths, though this practice has largely been abandoned. In more modern times, anvils have been placed upon bases fabricated from steel, often a short thick section of a largeI-beam. In addition, bases have been made from dimensional lumber bolted together to form a large block or steel drums full of oil-saturated sand to provide a damping effect. In recent times, tripod bases of fabricated steel have become popular.
There are many designs for anvils, which are often tailored for a specific purpose or to meet the needs of a particular smith. For example, there were anvils specifically made for farriers, general smiths, cutlers, chain makers, armorers, saw tuners, coach makers, coopers, and many other types of metal workers. Most of these anvil types look similar, but some are radically different. Saw maker anvils, for instance, are generally large rectangular blocks of steel that have a harder surface than most other anvils due to hammering on a harder steel for saws. Bladesmith anvils tend to be rectangular with a hardy and pritchel, but no horn. Such designs have originated in diverse geographic locations. Several styles of anvils include Bavarian, French Pig anvil, Austrian, and Chinese turtle anvil.
45-pound (20-kg) Bavarian-style anvil
The Bavarian style is known for the sloped brow. The brow was first used in medieval times to make armor on the church windows below the brow. Common manufactures include Söding Halbach and Holthaus. This style of anvil is known not to sway in the face due to the extra mass with the brow.
The commonblacksmith's anvil is made of either forged or cast steel, forged wrought iron with a hard steel face orcast iron with a hard steel face. Cast-iron anvils are not used for forging as they are incapable of standing up to the impact and will crack and dent. Also, cast-iron anvils without a hard steel face do not have the rebound that a harder anvil would and will tire out the smith. Historically, some anvils have been made with a smooth top working face of hardened steel welded to a cast-iron or wrought-iron body, though this manufacturing method is no longer in use. At one end, the common smith's anvil has a projecting conicalbick (beak,horn) used for hammering curved work pieces. The other end is typically called the heel. Occasionally, the other end is also provided with a bick, partly rectangular in section. Most anvils made since the late 18th century also have ahardy hole and apritchel hole where various tools, such as the anvil-cutter or hot chisel, can be inserted and held by the anvil. Some anvils have several hardy and pritchel holes, to accommodate a wider variety ofhardy tools andpritchels. An anvil may also have a softerpad for chisel work.
Steam hammer anvil
An anvil for apower hammer is usually supported on a massive anvil block, sometimes weighing over 800 tons for a 12-ton hammer; this again rests on a strong foundation of timber and masonry or concrete.
An anvil may have a marking indicating its weight, manufacturer, or place of origin. American-made anvils were often marked in pounds. European anvils are sometimes marked in kilograms. English anvils were often marked in hundredweight, the marking consisting of three numbers, indicatinghundredweight, quarter hundredweight and pounds. For example, a 3-1-5, if such an anvil existed, would be 3×112lb + 1×28lb + 5 lb = 369 lb ≈ 168 kg.
Cheap anvils made from inferior steel or cast iron and often sold at retail hardware stores, are considered unsuitable for serious use, and are often derisively referred to as "ASOs", or "anvil shaped objects".[2] In recent years, inexpensive cast steel anvils with hardened faces have become common, often sold online. Some blacksmiths consider these anvils suitable for beginners.[3] Amateur smiths have used lengths of railroad rail, forklift tines, or even simple blocks of steel as makeshift anvils.
A metalworkingvise may have a small anvil integrated into its design.
An anvil at the medieval construction site ofGuédelon inTreigny, France.A top view of a well-used London pattern anvil
Anvils were firstmade of stone, thenbronze, and laterwrought iron. Assteel became more readily available, anvils were faced with it. This was done to give the anvil a hard face and to stop the anvil from deforming from impact. Many regional styles of anvils evolved through time from the simple block that was first used bysmiths. The majority of anvils found today in the US are based on the London pattern anvil of the mid-19th century.
The wrought-iron steel-faced anvil was produced up until the early 20th century. Through the 19th and very early 20th centuries, this method of construction evolved to produce extremely high-quality anvils. The basic process involved forge-welding billets of wrought iron together to produce the desired shape. The sequence and location of the forge-welds varied between different anvil makers and the kind of anvil being made. At the same time cast-iron anvils with steel faces were being made in the United States. At the dawn of the 20th century solidcast-steel anvils began to be produced, as well as two-piece forged anvils made from closed-dieforgings. Modern anvils are generally made entirely from steel.
There are many references to anvils in ancient Greek and Egyptian writings, includingHomer's works. They have been found at theCalico Early Man Site inNorth America.
Anvils have since lost their former commonness, along with the smiths who used them. Mechanized production has made cheap and abundant manufactured goods readily available. The one-off handmade products of the blacksmith are less economically viable in the modern world, while in the past they were an absolute necessity. However, anvils are still used by blacksmiths and metal workers of all kinds in producing custom work. They are also essential to the work done byfarriers.
A typical metalworker's anvil, with horn at one end and flat face at the other, is a standard prop forcartoon gags, as the epitome of a heavy and clumsy object that is perfect for dropping onto an antagonist. This visual metaphor is common, for example, inWarner Brothers'Looney Tunes andMerrie Melodies shorts, such as those withWile E. Coyote and the Road Runner.[5] Anvils in cartoons were also referenced in an episode ofGilmore Girls, where one of the main characters tries to have a conversation about "Where did all the anvils go?", a reference to their falling out of use on a general scale.[6][7]Animaniacs made frequent gags on the topic throughout its run, even having a kingdom named Anvilania, whose sole national product is anvils.[8]
Josef Strauss:Feuerfest!, op. 269 (1869). The title means "fireproof". This was the slogan of the Wertheim fireproof safe company, which commissioned the work.[9]
The longest johns All the music is made using a hammer and anvil or vocals as the name suggests
Wagner'sRing des Nibelungen is notable in using the anvil aspitched percussion. The vast majority of extant works use the anvil asunpitched. Howevertuned anvils are available as musical instruments, albeit unusual. These are not to be confused with the "sawyers' anvils" used to "tune" big circular saw blades. Steel anvils are used for tuning for use as musical instruments, because those based partly on cast iron and similar materials give a duller sound; this is actually valued in industry, as pure steel anvils are troublesomely noisy, though energetically more efficient. The hammer and anvil have enjoyed varying popularity in orchestral roles.Robert Donington pointed out thatSebastian Virdung notes them in his book of 1510, andMartin Agricola includes it in his list of instruments (Musica instrumentalis deudsch, 1529) largely as a compliment toPythagoras. In pre-modern or modern times anvils occasionally appear in operatic works by Berlioz, Bizet, Gounod, Verdi, and Wagner for example. Commonly pairs of anvils tuned a third apart are used.
In practice modern orchestras commonly substitute abrake drum or other suitable steel structure that is easier to tune than an actual anvil, although a visibly convincing anvil-shaped prop may be shown as desired. InDas Rheingold Wagner scored for nine little, six mid-sized, and three large anvils, but orchestras seldom can afford instrumentation on such a scale.[10]
^Scott, Derek B. (2008).Sounds of the metropolis: the nineteenth-century popular music revolution in London, New York, Paris, and Vienna, p. 139. Oxford University Press, New York.ISBN978-0-19-530946-1.
