 | This article has multiple issues. Please helpimprove it or discuss these issues on thetalk page.(Learn how and when to remove these messages) (Learn how and when to remove this message)
|
Analog passthrough is a feature found on somedigital-to-analog television converter boxes. Boxes without the analog passthrough feature only allow older, analog-only TVs to view digital TV. Those with analog pass-through allow both digital and analog television to be viewed on older TVs.
Before digital television, passthrough originally existed inVCRs (and laterPVRs andDVDRs) that connected to a TV set usingRF connector, allowing theTV antenna orcable TV signal to be switched to pass through the VCR, or have VCR output added as an extra channel.
All digital-to-analog converter boxes have both an antenna input (which accepts thecoaxial cable that formerly went directly to the TV) and anRF output (which now goes directly to the TV). They may also have additional outputs. Any converter box converts the digital signal for the current digital sub-channel to an analog signal (at the reduced screen resolution of the analog standard), outputs that signal onto analog channel 3 or 4 (set by the user to avoid any conflict with local over-the-air channels) and sends that signal to the analog tuner on the TV. With a box that lacks analog passthrough, no other signals are sent to the output, so all analog stations are lost.
In the US, this primarily affects low-power andbroadcast translator stations, as these are exempt from theFCC mandate toswitch todigital broadcasting in 2009, as well as foreign signals that will remain in analog form. A small number of TV receivers were also manufactured with built-inbroadcast radio receivers; these included some small portable devices or (more rarely) sets marketed for hotel/motel use. If used with DTV converter boxes, these will need analog passthrough in order not to block incomingFM radio signals.[1]
Someconverter boxes offer analog pass-through, meaning that the same outputcable which carries the converteddigital signal (on analog channel 3 or 4) while the converter is operating also retains all remaininganalog signals upon turning the converter box off.
While this typically works to some extent with the converter box on, there is often significant signal strength reduction and/or interference on the original analog channels.
Analog pass-through signals are passed only to thecoax output, not to any other outputs provided by the unit. While other converter outputs may still be connected and used for digital TV reception, the coaxial RF output must remain connected to pass analog TV signals.
Some VCRs and TVs have receivers that detect active composite video or S-video connections. When they detect these connections, they are designed to accept signals only from those sources, which can cause issues with the described arrangement. In such a case, the two options would be to use the coax output exclusively, either when viewing analog TV only (which requires plugging and unplugging cables) or full-time (with the reduced digital TV quality produced using the coax output).
The majority of TVs have a button on the unit and/or remote labeled something like "TV/VIDEO", "INPUT" or "AUX", which manually switches between coax and other sources. This eliminates problems when using both sets of connections simultaneously.
| This section may contain informationnotimportant or relevant to the article's subject. Please helpimprove this section.(September 2022) (Learn how and when to remove this message) |
In the US, conversion to digital TV from analog was complete by June 12, 2009.
Unfortunately, only one of the initially available converter boxes included this feature,[citation needed] and a year before the original transition date of February 17, 2009,Community Broadcasters Association president Ron Bruno said four of the 32 NTIA-certified boxes had the feature.[2] In late March 2008, the CBA filed alawsuit in theU.S. Court of Appeals for the District of Columbia, seeking aninjunction to halt the sale and distribution of DTVconverter boxes,[3] charging that their failure to include analog tuners or analog passthrough violates theAll-Channel Receiver Act.[4] CBA maintained that the lack of analog support would seriously harm theLPTV andclass A television stations the group represents, as it is cost-prohibitive for many or most of them to convert to digital transmissions, and the new boxes would prevent viewers from being able to watch (or even being aware of the existence of) their analog-only stations.[5][6]
Responding to CBA's actions, theFCC and NTIA urged manufacturers to include the feature voluntarily in all converter boxes, and manufacturers responded by releasing a new generation of models with the feature. Some newDVD recorders andpersonal video recorders also provide both analog and digital tuners, and could therefore perform the basic functions of a set-top box in both modes.
In early May 2008, the D.C. district court denied the CBA petition without comment.[8] The court's decision implied that the association had not exhausted all its efforts. Furthermore, the court believed there wasn't enough merit to bring the case forward. The CBA responded by concentrating its lobbying efforts on the FCC and by urging more funding for low-power and Class A broadcasters to transition to digital, asking Congress to increase the number of such stations eligible for funds.
