Standard twisted-pair cable usable for most common types of Ethernet

8P8C plug

Ethernet over twisted-pair technologies usetwisted-pair cables for thephysical layer of anEthernet computer network. They are a subset of allEthernet physical layers.

Early Ethernet used various grades ofcoaxial cable, but in 1984,StarLAN showed the potential of simpleunshielded twisted pair. This led to the development of10BASE-T and its successors100BASE-TX,1000BASE-T,10GBASE-T and40GBASE-T, supporting speeds of 10 and 100 megabits per second, then 1, 10 and 40 gigabits per second respectively.^[a]

Two new variants of 10-megabit-per-second Ethernet over asingle twisted pair, known as10BASE-T1S and10BASE-T1L, were standardized in IEEE Std 802.3cg-2019.^[2] 10BASE-T1S has its origins in theautomotive industry and may be useful in other short-distance applications where substantial electrical noise is present.^[3] 10BASE-T1L is a long-distance Ethernet, supporting connections up to 1 km in length. Both of these standards are finding applications implementing theInternet of things. 10BASE-T1S is a direct competitor ofCAN XL in the automotive space and includes aPHY-Level Collision Avoidance scheme (PLCA).^[4]

The earlier standards use8P8C modular connectors^[b] and supported cable standards range fromCategory 3 toCategory 8. These cables typically have four pairs of wires for each connection, although early Ethernet used only two of the pairs. Unlike the earlier -T standards, the -T1 interfaces were designed to operate over a single pair of conductors and introduce the use of two new connectors referred to asIEC 63171-1^[5] andIEC 63171-6.^[6]

The first two early designs of twisted-pair networking wereStarLAN, standardized by theIEEE Standards Association asIEEE 802.3e in 1986, at one megabit per second,^[7] andLattisNet, developed in January 1987, at 10 megabits per second.^[8][9] Both were developed before the 10BASE-T standard (published in 1990 asIEEE 802.3i) and used different signaling, so they were not directly compatible with it.^[10]

In 1988, AT&T released StarLAN 10, named for working at10 Mbit/s.^[11] The StarLAN 10 signaling was used as the basis of 10BASE-T, with the addition oflink beat to quickly indicate connection status.^[c]

Using twisted-pair cabling in astar topology addressed several weaknesses of the previous Ethernet standards:

• Twisted-pair cables were already in use for telephone service and were already present in many office buildings, lowering the overall cost of deployment.
• The centralized star topology was also already often in use for telephone service cabling, as opposed to thebus topology required by earlier Ethernet standards.
• Using point-to-point links was less prone to failure and greatly simplified troubleshooting compared to a shared bus.
• Exchanging cheaprepeater hubs for more advancedswitching hubs provided a viable upgrade path.
• Mixing different speeds in a single network became possible with the arrival ofFast Ethernet.
• Depending oncable grades, subsequent upgrading toGigabit Ethernet or faster could be accomplished by replacing the network switches.

Although 10BASE-T is rarely used as a normal-operation signaling rate today, it is still in wide use withnetwork interface controllers inwake-on-LAN power-down mode and for special, low-power, low-bandwidth applications. 10BASE-T is still supported on most twisted-pair Ethernet ports with up toGigabit Ethernet speed.

The common names for the standards derive from aspects of the physical media. The leading number (10 in 10BASE-T) refers to the transmission speed in Mbit/s.BASE denotes thatbaseband transmission is used. TheT designates twisted-pair cable. Where there are several standards for the sametransmission speed, they are distinguished by a letter or digit following the T, such asTX orT4, referring to the encoding method and number of lanes.^[13]

ANSI/TIA-568 T568A termination

Pin	Pair	Wire[d]	Color
1	3	tip	white/green
2	3	ring	green
3	2	tip	white/orange
4	1	ring	blue
5	1	tip	white/blue
6	2	ring	orange
7	4	tip	white/brown
8	4	ring	brown

ANSI/TIA-568 T568B termination

Pin	Pair	Wire[d]	Color
1	2	tip	white/orange
2	2	ring	orange
3	3	tip	white/green
4	1	ring	blue
5	1	tip	white/blue
6	3	ring	green
7	4	tip	white/brown
8	4	ring	brown

Most Ethernet cables are wiredstraight-through (pin 1 to pin 1, pin 2 to pin 2, and so on). In some instances, thecrossover form (receive to transmit and transmit to receive) may still be required.

A cable for Ethernet may be wired to either theT568A or T568B termination standard at both ends of the cable. Since these standards differ only in that they swap the positions of pairs 2 and 3 – the only pairs used by the formerly common 10BASE-T and 100BASE-TX – a cable with T568A wiring at one end and T568B at the other functions as a crossover cable for the older, two-pair standards.

A 10BASE-T or 100BASE-TX host normally uses connector wiring calledmedium dependent interface (MDI), transmitting on pins 1 and 2 and receiving on pins 3 and 6. An infrastructure node (such as ahub or aswitch) normally uses the complementary wiring arrangement, calledMDI-X, theX standing for-crossover. MDI-X simply reverses the pairs, transmitting on pins 3 and 6 and receiving on pins 1 and 2. These ports are connected using astraight-through cable so each transmitter talks to the receiver on the other end of the cable. (Modern twisted-pair Ethernet uses all four pairs, differently, and the MDI–MDI-X distinction does not apply.)

Later equipment often can automatically switch between MDI and MDI-X arrangements as needed, obviating crossover cables and manual selection, but in the conventional arrangement, when two nodes having the same (fixed) type of port need to be connected, a crossover cable is required. If both devices being connected support 1000BASE-T, they will connect regardless of whether a straight-through or crossover cable is used.^[14]

A 10BASE-T transmitter sends twodifferential voltages, +2.5 V or −2.5 V. A 100BASE-TX transmitter sends three differential voltages, +1 V, 0 V, or −1 V.^[15] Unlike earlier Ethernet standards usingbroadband andcoaxial cable, such as10BASE5 (thicknet) and10BASE2 (thinnet), 10BASE-T does not specify the exact type of wiring to be used but instead specifies certain characteristics that a cable must meet. This was done in anticipation of using 10BASE-T in existing twisted-pair wiring systems that did not conform to any specified wiring standard. Some of the specified characteristics areattenuation,characteristic impedance,propagation delay, and several types ofcrosstalk. Cable testers are widely available to check these parameters to determine if a cable can be used with 10BASE-T. These characteristics are expected to be met by 100 meters of 24-gauge unshielded twisted-pair cable. However, with high-quality cabling, reliable cable runs of 150 meters or longer are often achievable and are considered viable by technicians familiar with the 10BASE-T specification.^{[citation needed]}

100BASE-TX follows the same wiring patterns as 10BASE-T, but is more sensitive to wire quality and length, due to the higherbit rates.

1000BASE-T uses all four pairs bi-directionally usinghybrid circuits andcancellers.^[16] Data is encoded using 4D-PAM5; four dimensions usingpulse-amplitude modulation (PAM) with fivevoltages, −2 V, −1 V, 0 V, +1 V, and +2 V.^[17] While +2 V to −2 V may appear at the pins of the line driver, the voltage on the cable is nominally +1 V, +0.5 V, 0 V, −0.5 V and −1 V.^[18]

100BASE-TX and 1000BASE-T were both designed to require a minimum ofCategory 5 cable and also specify a maximum cable length of 100 metres (330 ft).

10BASE-T and 100BASE-TX require only two pairs (pins 1–2, 3–6) to operate. Since common Category 5 cable has four pairs, it is possible to use the spare pairs (pins 4–5, 7–8) in 10- and 100-Mbit/s configurations for other purposes. The spare pairs may be used forpower over Ethernet (PoE), for twoplain old telephone service (POTS) lines, or for a second 10BASE-T or 100BASE-TX connection. In practice, great care must be taken to separate these pairs as 10/100-Mbit/s Ethernet equipmentelectrically terminates the unused pins ("Bob Smith Termination").^[19] Shared cable is not an option for Gigabit Ethernet as 1000BASE-T requires all four pairs to operate.

In addition to the more computer-oriented two and four-pair variants, the10BASE-T1,^[20]100BASE-T1^[21] and1000BASE-T1^[22]single-pair Ethernet (SPE) physical layers are intended forAutomotive,IoT, andM2M applications^[23] or as optional data channels in other interconnect applications.^[24] The distances that single pair operates at full duplex depends on the speed: 1000 m (1 km) with 802.3cg-2019 10BASE-T1L; 15 m (49 ft) with 100BASE-T1 (link segment type A); up to 40 m (130 ft) using 1000BASE-T1 link segment type B with up to four in-line connectors. Both physical layers require a balanced twisted pair with animpedance of 100 Ω. The cable must be capable of transmitting 600 MHz for 1000BASE-T1 and 66 MHz for 100BASE-T1. 2.5 Gbit/s, 5 Gbit/s, and 10 Gbit/s over a 15 m single pair is standardized in 802.3ch-2020.^[25] In June 2023, 802.3cy added 25 Gbit/s speeds at lengths up to 11 m.^[26]

Similar to PoE,Power over Data Lines (PoDL) can provide up to 50 W to a device.^[27]

Single-pair Ethernet (SPE)

Wire colour	PMA Signal
	BI_DA+
	BI_DA−

• 8P8C modular connector: For stationary uses in controlled environments, from homes todatacenters, this is the dominant connector. Its fragile locking tab otherwise limits its suitability and durability. Bandwidths supporting up toCat 8 cabling are defined for this connector format.
• M12X: This is theM12 connector designated for Ethernet, standardized as IEC 61076-2-109. It is a 12 mm metal screw that houses 4 shielded pairs of pins. Nominal bandwidth is 500 MHz (Cat 6A). The connector family is used in chemically and mechanically harsh environments such as factory automation and transportation. Its size is similar to the modular connector.
• Single-pair Ethernet defines its own connectors:
  • IEC 63171-1LC:^[5] This is a 2-pin connector with a similar locking tab to the modular connector, if thicker.
  • IEC 63171-6industrial:^[6] This standard defines five 2-pin connectors that differ in their locking mechanisms, and one 4-pin connector with dedicated pins for power. The locking mechanisms range from a metal locking tab toM8 and M12 connectors with screw or push-pull locking. The 4-pin connector is only defined with M8 screw locking.

Ethernet over twisted-pair standards up through Gigabit Ethernet define bothfull-duplex andhalf-duplex communication. However, half-duplex operation for gigabit speed is not supported by any existing hardware.^[28][29] Higher speed standards,2.5GBASE-T up to40GBASE-T^[30] running at 2.5 to40 Gbit/s, consequently define only full-duplex point-to-point links which are generally connected bynetwork switches, and do not support the traditional shared-mediumCSMA/CD operation.^[31]

Many different modes of operations (10BASE-T half-duplex, 10BASE-T full-duplex, 100BASE-TX half-duplex, etc.) exist for Ethernet overtwisted pair, and mostnetwork adapters are capable of different modes of operation.Autonegotiation is required in order to make a working 1000BASE-T connection.

When two linked interfaces are set to differentduplex modes, the effect of thisduplex mismatch is a network that functions much more slowly than its nominal speed. Duplex mismatch may be inadvertently caused when an administrator configures an interface to a fixed mode (e.g.100 Mbit/s full-duplex) and fails to configure the remote interface, leaving it set to autonegotiate. Then, when the auto-negotiation process fails, half-duplex is assumed by the autonegotiating side of the link.

• Classic Ethernet
• 25-pair color code
• Copper cable certification
• Ethernet extender
• Network isolator
• PHY-Level Collision Avoidance, used in 10BASE-T1
• Structured cabling

• How to Make a Network Cable, a how-to article fromwikiHow
• How to create your own Ethernet Cables

• Ethernet cables
• Physical layer protocols
• Local loop

• Articles with short description
• Short description matches Wikidata
• Use American English from March 2019
• All Wikipedia articles written in American English
• All articles with unsourced statements
• Articles with unsourced statements from February 2011