 | This articleneeds additional citations forverification. Please helpimprove this article byadding citations to reliable sources. Unsourced material may be challenged and removed. Find sources: "Train inspection system" – news ·newspapers ·books ·scholar ·JSTOR(April 2011) (Learn how and when to remove this message) |
 | The examples and perspective in this articlemay not represent aworldwide view of the subject. You mayimprove this article, discuss the issue on thetalk page, orcreate a new article, as appropriate.(October 2023) (Learn how and when to remove this message) |
Atrain inspection system is one of various systems of inspection which are essential to maintain the safe running ofrail transport.
Becausesafety is of high importance whentrain cars move across the rails, there must beinspections. The cars are heavy and have moving parts that can break or become defective. Worn or broken parts can drag, pound, and generally destroy the cars and thetrack structure they run on. Parts andloads must not extend outside the limits of the car, and there should be no leaking of the cars' contents.
Quality inspections are needed not just before atrain is moved, but also as it travels to its destination.
There are several levels of inspection on railroad equipment. Inspections are continuous, starting when the car is being built and repeated at regular intervals.
Before the train begins its journey, thelocomotives and thecars are checked. This is done by mechanical department workers, sometimescameras andscanners are also used. Some of the items certifiedgood to go are things like thebraking system including hand-brake release, brake application, condition of the air valves, piping and hoses, communication equipment, and many more. Very much like thechecklist an airline might use. When the pretrip work is done, the train is considered safe to move.
Once the movement begins, the train is continuously watched by employees, scanners and monitors. These are sometimes called "in motion defect detectors" ordefect detectors (DD).
As the railroad has evolved from block stations and control towers to a centralized dispatching system, they have also moved to more advanced inspection tools. The technologies in use today vary from a simplistic paddle and switch to infraredthermography,laser scanning, and evenultrasonic audio analysis. These devices are used to inspect engines, cars and the loads on them.[1]
The systems used onNorth American and other railways fall into a dozen or so major groups, some are listed below.
High impact wheels have some defect where it does not roll smoothly along the track.[2][3] A flaw in a wheel causes vibrations or banging. This is very destructive to the track structure and therolling stock.
Checks for overloads or shifted loads that can be dangerous.[3]
Looks forhunting oscillation of thetrucks orwheelset; a lateral movement in thegauge of the track, like drifting back and forth in a lane of traffic. This action can increase above a certain speed to the point the wheel flanges impact the rails, potentially causing damage to both. There is also force absorbed by this action that will affect the energy consumption of train operations.
Is stiff or poorly steering or axle sets that don't follow the path of the track correctly. Presents itself like 'dog tracking" where thetrucks are biased to run against the flange on one side or the other. Truck performance defects include tracking position and angle of attack on a per-axle basis, as well as rotation, shift, inter-axle misalignment, and tracking error on a per-bogie basis. Truck performance detectors can provide early detection of bogie defects, and early warning of derailment risks through flange climb or rail break.[4]
Listens with specialmicrophones for internalbearing defects as the equipment moves across the detector.[5][6] These are very sensitive and can detect problems before the bearing fails.
Look for hot wheels, which are generally caused by braking equipment failures. This equipment may be combined with bearing temperature detectors (below).[7]
This type of defect detector uses ultra sensitiveinfrared cameras calledpyrometers. These devices take thetemperature of each bearing as it passes by the scanner.[7] This data is then compared to preset "Alarm limits". If the wholeconsist is without problems, the train is passed. If however there is overheating in one or more of the bearings (ahot box), an alarm is given.
These messages can be by radio to the train crew or might be sent to thedispatch center for handling. The data is also used to detect a trend over several locations that might predict a future failure. If an alarm is sent, the train is stopped, and either the defect is corrected or the offending car is removed for repair. Manyderailments are avoided by these devices which is why thousands of them are in use on rail systems across the world.
As the name suggests, they are able to detect things hanging or dragging under the cars. These consist of a series of plates mounted on a pivot shaft. An object hanging or dragging will contact the plates, moving them and breaking a circuit. This will trigger an alarm and alert the crew. Many are stand-alone detectors, but most often are integrated into bearing temperature scanning locations.
These are able to measure the height and width of rolling stock, so that cars and loads which won't fit under bridges or through tunnels are stopped. Most often they are optical line of sight devices that trigger an alarm when the beam is broken. They are often seen at a bearing temperature scanning locations, they then report out as part of the detectors regular train inspection report. Mounted on poles or a bridge structure, the optical line is adjusted for a set height and width, it can then send an alarm when something too big to fit the clearance limits ahead passes its view.
Is a simple "broken wire" type device that notifies the train crew they are off the track somewhere in their train.
A system which monitors the integrity of thepantograph.[8] These are normally based on avision system which takes pictures of the pantographs and performs an analysis based on computer vision algorithms. A pantograph uses acarbon strip to conduct electricity between thecatenary and thepantograph. When these are damaged or worn out, thepantograph can tear down thecatenary causingtrain delays.
Laser and optical scanning wayside inspection devices (known as TBOGI—Truck Bogie Optical Geometry Inspection Systems) make images of theflange andtread. These measurements are compared with acceptable dimensions. When worn beyond limits, the wheels are scheduled for replacement. If beyond a safe level the axle set is removed from service.[9]
Theseback office systems are predictive, finding equipment problems as they start to develop.[6]
{{cite web}}: CS1 maint: archived copy as title (link)